Categories: Knowledge Center

Rethinking Part Consolidation With Additive Manufacturing

Previously published on fastradius.com on February 20, 2019

Mechanical assemblies are common in both consumer products and industrial products. Even relatively inexpensive products can have dozens of individual components, and in complex machinery there can easily be hundreds or thousands of components. Additive manufacturing (AM) allows for high levels of part consolidation, sometimes even removing the need for assembly.

The Benefits of Additive Manufacturing for Part Consolidation

AM is uniquely capable of producing complex geometries that can’t be manufactured using traditional methods of manufacturing. A mechanical assembly that would normally have many parts fabricated as separate components and then brought together can be additively manufactured as a single unit, even if the geometry is very complex. In addition to design simplification, there are other tangible benefits to using AM for part consolidation:

Lower overall projection costs

The best and most obvious benefit of consolidating your parts with AM is that needing fewer parts to assemble means you’re spending less money on assembly costs. Taking assembly out of the equation also means that you’ll reduce potential cost-driving factors such as quality control or inventory management. By using additive manufacturing to make multiple parts as one, you’re lessening the risk of hidden costs and project delays.

Less material

In traditional manufacturing, as part complexity increases, part cost also typically increases. With AM, this is not the case – as part complexity increases, part cost does not increase. In many cases the part cost will decrease, because increased complexity often means less material is being used. When using AM, it’s possible to achieve upwards of a 70 percent decrease in materials used compared to traditional manufacturing.

Lower overall risk

Part consolidation reduces or entirely eliminates a number of risks. For example, you can circumvent the risk that your supplier can no longer supply the part in question. This supplier risk is multiplied by the number of parts in the assembly. If you’re able to print multiple parts as a single unit using AM, the chances of encountering this issue greatly decrease.

There are other risks that are reduced as well. The instances of part failure decrease when the part has been manufactured as a single unit rather than assembled separately. Another risk is obsolescence; when the part reaches the end of its life you will not have remaining inventory that must be disposed.

Better performance

In many cases, AM allows you to make a better performing part, because it enables geometries that are desirable but that can’t be made with legacy manufacturing. Some of the applications of AM that have exciting benefits for improved product performance include light weighting, high strength to weight ratio, heat transfer and fluid flow, and energy absorption.

How Can You Identify Parts for Consolidation?

When thinking about part consolidation with AM, the first step is to focus on the function of the assembly that you plan on replacing. Then you need to question the assumptions that led to your original design made using traditional manufacturing.

It can be helpful to use a structured approach to analyzing the parts to be consolidated. An effective and popular methodology for analyzing manufacturing and assembly is known as Design for Manufacture and Assembly (DFMA®). The model is made up of three questions that help engineers and manufacturers begin the assembly consolidation process:

  1. Does the part need to move relative to the parts assembled?
  2. Are multiple materials needed for the part function?
  3. Does the part need to be separated for assembly or disassembly?

By thinking through these questions, designers can determine the theoretical minimum number of parts required for assembly. While these questions can serve as a starting point, there are a few follow up considerations that will help you determine if you should be thinking of additive for part consolidation:

  1. Are multiple parts needed to satisfy this requirement?
  2. Can a single part satisfy this requirement?

In other words, are multiple parts truly needed for the part to function properly? Are there other solutions, such as lattice structures (or other complex geometries), that could be incorporated into a design that could essentially serve the same function while reducing the amount of parts and materials required overall?

Take a look at the chart below to help determine if part consolidation using additive is right for you. 

Part Consolidation and Additive Processes

Designing to reduce the number of separate components is only one factor in part consolidation. Another way to minimize the number of assembled parts in your product is to use technologies that make consolidation possible. With additive technologies, such as HP Multi Jet Fusion (MJF), separate components have the ability to not only be printed as one whole piece, but are capable of a full range of motion straight off the printer.

Deciding on which additive technology to use depends on your design requirements. For example, with HP MJF, parts do not require supports, which enabled engineers to create more complex designs and movable pieces. Carbon® technology does require supports, but is able to print durable components with varying wall thicknesses as one piece. A great example of part consolidation using Carbon® is Steelcase’s SILQ chair armrest: the armrest used to be assembled using three separate pieces, but thanks to lattice structures and complex geometries, is now printed as one.

Part Consolidation Application Examples

There are many applications that could benefit from part consolidation using AM. There are already applications on the market, such as mechanical assemblies, fluidic components, structural pieces, and more. Manufacturers are seeing increased performance and durability thanks to designing multiple parts as one. Let’s take a closer look at how part consolidation impacts two specific applications.

Pump impellers

Traditionally-manufactured impellers often require separate parts that are welded together. With AM, these can be printed as one single piece. When a pump impeller is traditionally manufactured, it will have gaps between its components. By manufacturing with additive, the gap can be removed – which improves the part’s overall performance. It’s also important to note that because the welded joints have been eliminated, the number of potential failure points have been reduced and corrosion at the welds will no longer occur.

Air ducting

Air ducts are also great candidates for part consolidation. Using complex geometries enabled by additive, the part geometry and air flow can be optimized. A case example of this is a cooling duct in the HP 500/300 printer series that utilizes HP MJF. By consolidating eight parts into one, HP was able to simplify their supply chain and lower the component cost by 30 percent.

Manufacturers strive to achieve the reduction cost, supply chain risk, and improved performance through part consolidation. AM offers a unique opportunity to further reduce assemblies due to the complex geometries that are now possible. If you want to learn more about how your application can be consolidated, contact our team of experts today.

SyBridge Technologies

Recent Posts

How SyBridge Expertise Optimizes Your Process and Lowers Costs

How SyBridge Expertise Optimizes Your Process and Lowers Costs In the fast-paced world of manufacturing,…

5 days ago

2024 Trends in Cosmetic Packaging

Imagine a world where your product stands out on crowded shelves, not just visually, but…

1 month ago

7‌ ‌Common‌ ‌Injection‌ ‌Molding‌ ‌Defects‌ ‌and‌ ‌How‌ ‌to‌ ‌Avoid‌ ‌Them‌

Injection molding is an efficient production method when high volumes of identical parts are needed. However,…

3 months ago

Critical Design Guidelines for Urethane Casting

As a production method, urethane casting sits in stark contrast to the hard tooling of injection molding. Whereas injection…

3 months ago

The Ultimate CNC Design for Manufacturability (DFM) Checklist

CNC machining is among the most popular manufacturing methods because the process is highly versatile, repeatable,…

4 months ago

HP Multi Jet Fusion Design Guidelines

Originally published on fastradius.com on October 20, 2021 Multi Jet Fusion enables the efficient production…

5 months ago